Adjustable bed not working? What to check before you call for service
Hi, we’re John and Mimi. When an adjustable base that worked yesterday won’t move today, it’s easy to assume the motor is gone. Most of the time it’s something much smaller: a plug that worked loose, a power strip that switched off, a remote with tired batteries, or a sync cable that came apart when someone vacuumed under the bed. Here are the checks we’d walk you through on the phone, in the order we’d do them, plus what to do if the bed is stuck up during a power outage and exactly what to send us if it really is a warranty problem.
A safety note first: if you smell burning, see smoke or sparks, or a cord or plug feels hot, unplug the base (only if you can do it safely) and stop using it until it’s been checked. Keep kids, pets and hands out from under the base while it moves, and never reach into the frame while someone is pressing the remote.
The short answer
- Check power first. Is the base plugged straight into a working wall outlet, and is every cable between the plug, the control box and the motors pushed all the way in?
- Then the remote. Fresh batteries in a wireless remote, and if it still does nothing, it may need to be paired with the control box again (the steps are in your base’s manual).
- Restart it. Unplug the base, wait a minute, plug it back in and try again, the same as you would with any electronic device.
- Stuck up in an outage? Every base we sell except the SBKDH lists an emergency backup battery strip or box. With fresh 9-volt batteries in it, it’s there so you can lower the bed without wall power.
- Still nothing? Text John a short video of what happens when you press the buttons. If it’s a defect, it’s covered by the base’s 10-year limited warranty, with full coverage in year 1 and motors covered for 2 years.
First check: power, plugs and the outlet
- Test the outlet. Plug a lamp or phone charger into the same outlet. If it doesn’t work either, check for a wall switch that controls the outlet, a tripped breaker, or a GFCI outlet that needs its reset button pressed.
- Follow every cable. Bases get bumped when the bed is moved, cleaned under or when the mattress is changed. Make sure the power cord is firmly in the wall and in the base, and that the cables to the control box are seated all the way.
- Skip the chain of power strips. The Electrical Safety Foundation International (ESFI) says multiple-plug outlets must be plugged directly into a wall receptacle and can’t be chained together, and that an extension cord is a temporary solution, not a long-term extension of your home’s wiring. If your base is on a power strip, check that the strip is switched on and hasn’t tripped, or try the base straight in the wall.
- Look at the cord itself. ESFI says never to use a cord that feels hot or is damaged in any way. A moving base can pinch a cord that’s draped through the frame, so route cords away from hinges and the lifting parts. The U.S. Consumer Product Safety Commission (CPSC) also says not to run extension cords under carpets, through doorways or under furniture, which includes under the bed.
- Plan for the outlet before you call. Our Warranty page says the adjustable base warranty doesn’t cover unauthorized service calls to show you how to use the base or to find a working power outlet, so these checks can save you a bill.
When the remote does nothing
- Wired remote (SBKDH). The SBKDH uses a wired 2-button remote, so check that its cable is plugged in firmly and isn’t pinched or cut.
- Wireless remote: batteries first. Put in fresh batteries, checking which way they face. Weak batteries can make a remote work only from close up, or only some of the time.
- Pair it again. A wireless remote talks to the control box, and if that link is lost the remote may light up but the bed won’t move. The pairing steps are in the instruction manual that came with your base; if you’ve lost it, text John your model code and he’ll help.
- Try the restart. Unplug the base for a minute, plug it back in, then try the remote again (and pair again if your manual says to after a power loss).
- Lost or broken remote on an e3? We sell the replacement wireless remote for the e3 (model WRKD3). The listing says it’s compatible with the SBKD2 and SBKD3 and will need to be paired with your control box once you receive it. For any other base, text John your model code before you order a remote.
- Voice or app control. The Glide listing says its voice control works through the built-in microphone with an app download, and the SBKDT2 lists Bluetooth built into the control box. If voice or the app stops working but the remote still moves the bed, the base is fine; check the app connection on your phone.
Stuck raised when the power goes out
This is the call that worries people most, and it’s why the backup battery matters. Every base we sell except the SBKDH lists an emergency backup battery strip or box, and the e3, e4 Premium and Glide listings say their battery strip runs on 9-volt batteries. How the strip connects is shown in your manual. A few tips:
- Put batteries in now. Fresh 9-volt batteries at setup, and a reminder to swap them when you change your smoke alarm batteries, means the strip is ready when the lights go out.
- Use it to lower the bed. Think of the backup as a way to bring the base back down in an outage, not to run it for days. Once the bed is flat, you can sleep on it like any other bed until the power is back.
- SBKDH owners. Its listing doesn’t mention a battery backup. If the head is up when the power goes out, text John and he’ll tell you what your options are.
If you rely on a raised bed for health reasons, talk with your doctor about a plan for outages, and see our aging in place guide for other ideas.
Only one side moves on a split king
A split king is two Twin XL bases, each with its own motors, control box and plug. If one side works and the other doesn’t, check the dead side on its own: its plug, its outlet, its remote. If the two sides are supposed to move together, check the synchronization cable between them. The e3 and e4 Premium listings describe it as the ability to control your side and your partner’s side separately or synchronize the two bases together, and the Glide, e7 Lumbar and SBKDT2 list a sync cable too. A cable that was knocked loose is the usual reason two synced sides stop matching. For how the sides connect in the first place, see our split king adjustable base guide.
Massage, lights or USB ports not working
- Everything runs on the same power. Massage, under-bed lights and USB ports all depend on the base being plugged in, so if none of them work, go back to the power checks above.
- Massage timers. The e4 Premium, Glide, e7 Lumbar, SBKDT2 and e8 listings describe a massage timer (10, 20 or 30 minutes on most), so massage that stops on its own may simply have timed out.
- Motion sensor lights. The e7 Lumbar’s night light has a motion sensor that turns on when it senses movement, so it isn’t meant to stay on all night.
- USB charging. Try a different cable and phone before deciding the port is bad. The e7 Lumbar lists both USB-A and USB-C ports.
Noises, wobbles and a mattress that won’t stay put
- Clicking or rubbing. Raise the base and look for a pillow, blanket, cord or toy caught in the frame, and check that the mattress or base isn’t rubbing a headboard, wall or nightstand. If your base glides toward the wall as it rises, see our wall hugger adjustable bed guide.
- Wobbling. On bases with screw-in legs, make sure every leg is screwed in all the way and all are the same height. On zero clearance setups, the hook and loop straps in the listings secure the base to a slat system.
- Mattress sliding down. Check that the mattress retainer bar is in place at the foot, and see how to keep a mattress from sliding on an adjustable base.
- Struggling to lift. Most of our bases list a 750 lb weight limit including the mattress and the people on it (the SBKDH lists 700 lbs), and going over it may void the warranty. See adjustable bed weight capacity.
Is it a warranty problem? What to send us
If you’ve tried the checks above and the base still won’t move, or a motor hums but nothing lifts, it’s time to text us. Our adjustable bases carry a 10-year limited warranty, and the coverage changes over time:
| When | What our Warranty page says |
|---|---|
| Year 1 | Any defective part is repaired or replaced at no cost, including authorized labor and transportation |
| Years 1 and 2 (motors) | A failed motor is fully replaced, including parts, labor and transportation |
| Years 2 to 5 | Defective parts are replaced; you pay service, installation and transportation, and send the old part back within 14 days |
| Years 6 to 10 | Prorated replacement parts (1/180 of the part’s current cost for each month past year 5), plus freight and service |
To file, text or call John at 818-924-3744 or email john@mimijohn.com with your order number, a short description, photos of the problem and of the law label, and ideally a short video of what happens when you press the buttons. Don’t ship anything back until we contact you. The Warranty page lists what isn’t covered, including misuse, an improper power supply, repairs by an unauthorized person and use over the weight limit. The full terms are on our Warranty page, and our mattress warranty explained guide walks through them in plain English.
The replacement remote and our bases at today’s prices
If a part or a whole base really is needed, here’s what we sell today. Prices are read live from our catalog.
| Pick | Best for | Model code | Twin XL | Queen |
|---|---|---|---|---|
| SBKDH | Head lift only, wired 2-button remote; no battery backup listed | SBKDH-TL |
$399 | $439 |
| e3 (SBKD3) | Head and foot lift, wireless 9-button remote, 9-volt battery backup strip, sync cable for split sets | SBKD3-TXL |
$449 | $499 |
| e4 Premium (SBKDP2) | Adds massage, USB ports and under-bed lighting; wireless 14-button remote | SBKDP2-TL |
$599 | $659 |
Prices are today’s prices, read live from our catalog, with free FedEx shipping included. “Not offered” means that model isn’t made in that size.
Comparing every feature, including which bases have battery backup and sync cables? See how to choose an adjustable base or the adjustable base comparison chart. Setting up a new one? Start with how to set up an adjustable base.
Shop this guide
Parts and bases people ask about when a base stops working.
- Replacement Wireless Remote for e3 (SBKD3) Adjustable Base, from $99. Replacement wireless remote for the e3 (also compatible with the SBKD2); pairs with your control box.
- e3 Adjustable Bed Base with Wireless Remote, Memory Positions & Zero Clearance, from $449. Head and foot lift with a 9-volt battery backup strip.
- Adjustable Base - SBKDH, from $399. The simplest base we sell: head lift with a wired remote.
Questions we hear a lot
Why is my adjustable bed not working?
Most often it is power: a plug that worked loose, an outlet on a wall switch or tripped GFCI, a power strip that is off, or a cable to the control box that came apart. Next check the remote: fresh batteries in a wireless remote, then pairing it with the control box again using the steps in your manual. Unplugging the base for a minute and plugging it back in is also worth a try.
How do you lower an adjustable bed when the power is out?
Use the emergency backup battery. Every base we sell except the SBKDH lists an emergency backup battery strip or box, and the e3, e4 Premium and Glide listings say theirs runs on 9-volt batteries. Put fresh batteries in at setup so it is ready, and follow your manual for how it connects.
Why is my adjustable bed remote not working?
Try fresh batteries first, then pair the remote with the control box again (the steps are in your base manual), and check that the base itself has power. The SBKDH uses a wired remote, so check its cable instead. For the e3 we sell a replacement wireless remote (WRKD3), which the listing says is compatible with the SBKD2 and SBKD3 and must be paired once you receive it.
Why does only one side of my split king adjustable bed work?
A split king is two Twin XL bases, each with its own plug, control box and remote. Check the side that does not move on its own: its plug, its outlet and its remote. If the two sides should move together, check that the synchronization cable between them is connected.
Is a broken adjustable base covered by the warranty?
A defect is. Our adjustable bases carry a 10-year limited warranty: full coverage in year 1, motors fully replaced for 2 years, replacement parts in years 2 to 5 and prorated parts in years 6 to 10. The Warranty page says it does not cover service calls just to show you how to use the base or to find a working power outlet, misuse, an improper power supply or use over the weight limit. Text John your order number, photos and a short video to start a claim.
Text John before you buy a part
Text John your order number or your base’s model code (it’s on the product page), what happens when you press the buttons, and a short video if you can. Most problems are fixed with a plug, batteries or pairing, and he’ll tell you honestly if you don’t need to buy anything. Text or call 818-924-3744, 6 AM to 9 PM Pacific.
Written by John & Mimi Venti, MimiJohn. Product and warranty details are from our product listings and our Warranty page, checked November 22, 2026; always follow the instruction manual that came with your base for pairing, reset and battery steps. Cord safety points are from the Electrical Safety Foundation International (Extension Cord Safety Tips) and the U.S. Consumer Product Safety Commission (Publication 5032, Household Extension Cords Can Cause Fires), checked November 22, 2026. This is general guidance, not electrical advice; for wiring or outlet problems, call a licensed electrician. Prices are read live from our catalog and update automatically.